wiki:VirtualMemory

Version 29 (modified by gao, 15 years ago) (diff)

Add the description of MMU mode values

TSAR MMU

The TSAR MMU (Memory Management Unit) is an hardware component implemented as a L1 cache controller. This generic component can be used with any single instruction issue, 32 bits processor.

As the processor core can issue two simultaneous instruction and data requests, there is actually two separated MMUs for data and instructions. These two MMUs share the same physical access to the VCI/OCP interconnect. Each MMU contains a set-associative cache and a TLB (Translation look-aside buffer), that is in charge of the virtual to physical address translation, and perfoms access right verifications.

The Tsar generic MMU implements a paginated virtual memory, supporting two page sizes : 4 Kbytes pages, and 2 Mbytes pages. In order to be independent on the processor core choice, the TLB MISS are handled by an hardwired Finite State Machine (called a Table Walk), without any software action.

1. Virtual Memory

The TSAR architecture defines two page sizes : 4 Kbytes pages, and 2 Mbytes pages. The virtual address space size is 4 Gbytes (32 bits virtual addresses). The physical address space is limited to 1 Tbytes (40 bits physical addresses). The page table are build by the operating system, and are stored in the main memory. Each execution context (such as an UNIX process) has is own page table.

1.1 Two levels Page Table structure

As described below, the Page Table has a hierarchical two levels structure :

  • All page tables (first & second level) must be aligned : the page table base adress must be a multiple of 8K bytes for a first level page table, and multiple of 4K bytes for a second level page table.
  • The page tables can be placed anywhere in the physical address space.
  • The PTPR register is located in the generic MMU, and is re-initialised by the OS at each context switch. It contains the 27 MSB bits of the first level page table base address, and is extended (left-shifted) to 40 bits by the Table-Walk FSM in case of TLB MISS.

1.2 First Level Page Table Entry Format

Each entry in a first level page table can contain either a 2M bytes page descriptor (called PTE1), or a second level page table descriptor (called PTD1). It is implemented as a single 32 bits word :

  • PTE1 :
VTLRCWXUGD reserved (3 bits) PPN1 (19 bits)
  • PTD1
VT reserved (2 bits) PTBA (28 bits)

The various fields are defined as follows :

V Valid bit Valid entry when 1 (set by the OS)
T Type bit PTD1 when 1 (set by the OS)
L Local access bit Used by the OS for page replacement (set by the hardware)
R Remote access bit Used by the OS for page replacement (set by the hardware)
C Cachable bit The page is cachable in the L1 cache when 1 (set by the OS)
W Writable bit The page is writable when 1 (set by the OS)
X eXecutable bit The page can contain instructions when 1 (set by the OS)
U User bit The page is accessible in user mode when 1 (set by the OS)
G Global bit Entry not invalidated in TLB flush when 1 (set by the OS)
D Dirty bit The page has been modified when 1 (set by the hardware)
PPN1 Physical Page Number Concatened to the page offset to build the physical address
PTBA Page Table Base Address Second level page table base address

The L, R, D bits are used by the operating system to implement the page replacement policy.

  • The D bit is set by the hardware, when a page is written and when it is not already set, using an atomic access (LL/SC).
  • The L bit is set by the hardware, when the page is accessed by a local processor or coprocessor, after a TLB miss, and when it is not already set.
  • The R bit is set by the hardware, when the page is accessed by a remote processor or coprocessor, after a TLB miss, and when it is not already set.

These page table updates use atomic access (LL/SC).

If the entry is a PTE1, the PPN1 value (19 bits) must be concatened with the page offset (21 bits) to build the 40 bits physical address.

If the entry is a PTD1, the PTBA value (28 bits) must be left-shifted by 12 bits to define the base address of the level 2 page table. The page table being aligned in memory, the 12 LSB bits of this base address have a 0 value.

1.3 Second Level Page Table Entry Format

Each entry in a second level page table contains a 4K bytes page descriptor (called PTE2). It is implemented as two 32 bits words: the first word contains the flags; the second word contains the 28 bits physical page number (PPN2).

  • PTE2 first word :
VTLRCWXUGD reserved (22 bits)
  • PTE2 second word :
reserved (4 bits) PPN2 (28 bits)

The various fields are defined as follows :

V Valid bit Valid entry when 1 (set by the OS)
T Type bit Must be 0 for a PTE2 (set by the OS)
L Local access bit Used by the OS for page replacement (set by the hardware)
R Remote access bit Used by the OS for page replacement (set by the hardware)
C Cachable bit The page is cachable in the L1 cache when 1 (set by the OS)
W Writable bit The page is writable when 1 (set by the OS)
X eXecutable bit The page can contain instructions when 1 (set by the OS)
U User bit The page is accessible in user mode when 1 (set by the OS)
G Global bit Entry not invalidated in TLB flush when 1 (set by the OS)
D Dirty bit The page has been modified when 1 (set by the hardware)
PPN2 Physical Page Number Concatened to the page offset to build the 40 bits address

The L, R, D bits are used by the operating system to implement the page replacement policy.

  • The D bit is set by the hardware, when a page is written and when it is not already set, using an atomic access (LL/SC).
  • The L bit is set by the hardware, when the page is accessed by a local processor or coprocessor, after a TLB miss, and when it is not already set.
  • The R bit is set by the hardware, when the page is accessed by a remote processor or coprocessor, after a TLB miss, and when it is not already set.

These page table updates use atomic access (LL/SC).

The PPN2 value (28 bits) must be concatened with the page offset (12 bits) to build the 40 bits physical address.

2. MMU/processor interface

In order to be used with the various (32 bits, single instruction issue) processor cores available in the SoCLib library, the TSAR generic MMU defines a generic processor/MMU interface for data and instructions.

2.1 Instruction MMU interface

The Instruction MMU interface is defined by the following signals :

struct InstructionRequest {
        bool valid;
        uint30_t addr;
        enum ExecMode mode;
    };
struct InstructionResponse {
        bool valid;
        bool error;
        uint32_t instruction;
    };

The addr virtual address is a 32 bits word address. It is coded on 30 bits.

The possible values for the Execution Mode are defined below :

ExecMode? Value
Hyper *1
Kernel 00
User 10

2.2 Data MMU interface

The Data MMU interface is defined by the following signals :

struct DataRequest {
        bool valid;
        uint30_t addr;
        uint32_t wdata;
        enum DataOperationType type;
        uint4_t be;
        enum ExecMode mode;
    };
struct DataResponse {
        bool valid;
        bool error;
        uint32_t rdata;
    };

The addr virtual address is a 32 bits word address. It is coded on 30 bits.

The wdata field is only significant for be-masked bytes:

The possible values for the execution mode are the same as for the instructions.

The possible values for the OperationType? field are defined below :

Data.OperationType? R X L Z semantic
DATA_READ 1 0 0 0 load 32 bits from memory address space
DATA_WRITE 0 0 0 0 store 32 bits to memory adress space
DATA_LL 1 0 1 0 load 32 bits from memory address space with reservation
DATA_SC 0 0 1 0 conditionnal store 32 bits to memory address space
XTN_READ 1 1 0 0 load 32 bits from MMU register
XTN_WRITE 0 1 0 0 store 32 bits to MMU register
DATA_LLRST 0 0 0 1 reset a previous LL reservation

Note : Instruction request & data requests are independent : the processor can issue simultaneous data & instruction requests that have different execution modes.

In case of access to an eXTerNal register (XTN_READ or XTN_WRITE) the MMU register is identified by the Data.Address field. (see section 3).

3. MMU architecture

The generic MMU is implemented in the L1 cache controller.

As the processor core can issue two simultaneous instruction and data requests, there is actually two separated data and instructions caches, sharing the same physical access to the VCI/OCP interconnect. These cache are set associative, and have a total capacity of 16 Kbytes :

  • cache line width = 64 bytes
  • number of associative sets = 64 sets
  • number of associative ways = 4 ways

The data cache L1 implement a writhe-through policy, in order to simplify the cache-coherence protocol. It contains a write-buffer that is in charge to build write burst, with the following constraints :

  • the burst length is variable
  • the maximal burst length is 8 32 bits words
  • all addresses in a burst belongs to the same "half cache line" (32 bytes aligned)
  • each address in a burst can have a different Byte Enable value (including the 0 value)

Similarly, the L1 cache controller contains two separated hardware MMUs for instruction and data. Each MMU contains a 64 entries TLB (Translation Look-aside Buffer). These TLBs are implemented as set-associative caches (16 sets of 4 ways). Each entry in these TLBs can contain either a 4 Kbytes page descriptor, or a 2 Mbytes page descriptor. The figure below illustrate the general structure of the TSAR L1 caches.

For both data & instructions, the TSAR L1 caches use physical addresses : the cache directories are indexed by the physical addresses, and the tags contained in the directories are obtained from the physical addresses. The access to the L1 cache being a critical path, the TSAR MMU use a speculative approach to avoid to serialize the TLB access and the L1 cache access:

  • After each TLB hit, the input VPN and the resulting PPN values are saved in two VPN_save & PPN_save registers.
  • During access (n), the PPN_save value, corresponding to access (n_1) is used to access the cache. Simultaneously, the cache controller checks that the VPN value is equal to the VPN_save value (no page change).
  • In case of TLB hit with a page change, the cache must be accessed twice, which means one cycle penalty.

3.1 MMU activation

After general RESET, the the MMU is desactivated : As long as the MMU is not activated, the 32 bits virtual address is simply extended to 40 bits (for both data and instructions), by appending 8 nul bits and directly used as a physical address. As long as the caches are not activated, all read requests are considered uncached by the cache controller.

The instruction cache, the data cache, the instruction MMU and the data MMU can be separately activated by the software, by writing in the MMU_MODE register.

3.2 Generic MMU exceptions

The hardware MMU can signal exceptions by rising the general instruction_bus_error and data_bus_error signals (for an instruction or data accesss respectively). The error type is written in the INS_ERROR_TYPE & DATA_ERROR_TYPE registers, as described below:

Exception type code cause severity
MMU_PT1_UNMAPPED 0x001 Page fault on Table1 (invalid PTE) non fatal error
MMU_PT2_UNMAPPED 0x002 Page fault on Table 2 (invalid PTE) non fatal error
MMU_PRIVILEGE_VIOLATION 0x004 Protected access in user mode user error
MMU_WRITE_VIOLATION 0x008 Write access to a non write page user error
MMU_EXEC_VIOLATION 0x010 Exec access to a non exec page user error
MMU_UNDEFINED_XTN 0x020 Undefined external access address user error
MMU_PT1_ILLEGAL_ACCESS 0x040 Bus Error in Table1 access kernel error
MMU_PT2_ILLEGAL_ACCESS 0x080 Bus Error in Table2 access kernel error
MMU_CACHE_ILLEGAL_ACCESS 0x100 Bus Error during the cache access kernel error

3.3 generic MMU registers mapping

The generic MMU contains a set of registers (or pseudo-registers) that can be accessed by operating system, through a dedicated MMU driver. In the case of the MIPS processor, these registers are implemented in coprocessor 2, and are accessed using the mtc2 (write) and mfc2 (read) instructions.

These registers are described below :

register name index description mode
MMU_PTPR 0 Page Table Pointer Register R/W
MMU_MODE 1 Data & Inst TLBs Mode Register R/W
MMU_ICACHE_FLUSH 2 Instruction Cache flush W
MMU_DCACHE_FLUSH 3 Data Cache flush W
MMU_ITLB_INVAL 4 Instruction TLB line invalidation W
MMU_DTLB_INVAL 5 Data TLB line Invalidation W
MMU_ICACHE_INVAL 6 Instruction Cache line invalidation W
MMU_DCACHE_INVAL 7 Data Cache line invalidation W
MMU_ICACHE_PREFETCH 8 Instruction Cache line prefetch W
MMU_DCACHE_PREFETCH 9 Data Cache line prefetch W
MMU_SYNC 10 Complete pending writes W
MMU_IETR 11 Instruction Exception Type Register R
MMU_DETR 12 Data Exception Type Register R
MMU_IBVAR 13 Instruction Bad Virtual Address Register R
MMU_DBVAR 14 Data Bad Virtual Address Register R

The generic MMU Mode Register has four bits and these 16 values are described as below :

MODE3 MODE2 MODE1 MODE0 description
(INS TLB) (DATA TLB) (INS CACHE) (DATA CACHE)
0 0 0 0 TLBs and caches deactivated
0 0 0 1 TLBs and instruction cache deactivated, data cache actived
0 0 1 0 TLBs and data cache deactivated, instruction cache actived
0 0 1 1 TLBs deactivated, instruction and data cache actived
0 1 0 0 Instruction TLB and caches deactivated, data TLB actived
0 1 0 1 Instruction TLB and instruction cache deactivated, data TLB and data cache actived
0 1 1 0 Instruction TLB and data cache deactivated, data TLB and instruction cache actived
0 1 1 1 Instruction TLB deactivated, data TLB and caches actived
1 0 0 0 Data TLB and caches deactivated, instruction TLB actived
1 0 0 1 Data TLB and instruction cache deactivated, instruction TLB and data cache actived
1 0 1 0 Data TLB and data cache deactivated, instruction TLB and instruction cache actived
1 0 1 1 Data TLB deactivated, instruction TLB and caches actived
1 1 0 0 Caches deactivated, TLBs actived
1 1 0 1 Instruction cache deactivated, TLBs and data cache actived
1 1 1 0 Data cache deactivated, TLBs and instruction cache actived
1 1 1 1 TLBs and caches actived

Attachments (3)

Download all attachments as: .zip