source: trunk/boot/tsar_mips32/boot_spi_driver.h @ 608

Last change on this file since 608 was 547, checked in by nicolas.van.phan@…, 6 years ago

Implement bootloader SPI SD card driver (VERY SLOW)

Rectify boot_spi_driver frequency

File size: 4.5 KB
Line 
1///////////////////////////////////////////////////////////////////////////////////
2// File     : sdc_driver.h
3// Date     : 31/08/2012
4// Author   : cesar fuguet
5// Copyright (c) UPMC-LIP6
6///////////////////////////////////////////////////////////////////////////////////
7
8#ifndef BOOT_SPI_DRIVER
9#define BOOT_SPI_DRIVER
10
11#include <boot_spi_utils.h>
12
13///////////////////////////////////////////////////////////////////////////////
14// SD card structure definition
15///////////////////////////////////////////////////////////////////////////////
16struct boot_sdcard_dev
17{ 
18    // SPI controller pointer
19    struct boot_spi_dev * spi;
20
21    // block length of the SDCARD
22    unsigned int block_length;
23
24    // access pointer representing the offset in bytes used to read or write in
25    // the SDCARD. This driver is for cards SDSD, therefore this offset must be
26    // multiple of the block length
27    unsigned int access_pointer;
28
29    // slave ID. This ID represents the number of the slave select signal used
30    // in the hardware platform (SPI channel)
31    int slave_id;
32
33    // is the card high capacity ?
34    int sdhc;
35};
36
37///////////////////////////////////////////////////////////////////////////////
38// This function initializes the SPI controller and call sdc_open to
39// initialize  the SD card
40// - channel: channel to initialize (only channel 0 supported)
41// Returns 0 if success, other value if failure
42///////////////////////////////////////////////////////////////////////////////
43int boot_spi_init();
44
45///////////////////////////////////////////////////////////////////////////////
46// Transfer data between the block device and a memory buffer.
47// - lba       : first block index on the block device
48// - buf_paddr : base address of the memory buffer
49// - count     : number of blocks to be transfered.
50// Returns 0 if success, > 0 if error.
51///////////////////////////////////////////////////////////////////////////////
52int boot_spi_access( unsigned int       lba,
53                     unsigned long long buf_paddr,
54                     unsigned int       count);
55
56///////////////////////////////////////////////////////////////////////////////
57// SD card constants
58///////////////////////////////////////////////////////////////////////////////
59
60// Number of retries after an unacknowledge command
61#define SDCARD_COMMAND_TIMEOUT  100
62
63// This command is a simple SD commmand
64#define SDCARD_CMD              0
65
66// This is an application specific command
67#define SDCARD_ACMD             1
68
69// The transmition is done in the negative edge of the clock
70#define SDCARD_TX_NEGEDGE       0
71
72// The transmition is done in the positive edge of the clock
73#define SDCARD_TX_POSEDGE       1
74
75// The reception is done in the negative edge of the clock
76#define SDCARD_RX_NEGEDGE       0
77
78// The reception is done in the positive edge of the clock
79#define SDCARD_RX_POSEDGE       1
80
81///////////////////////////////////////////////////////////////////////////////
82// SD card macros
83///////////////////////////////////////////////////////////////////////////////
84
85///////////////////////////////////////////////////////////////////////////////
86//   SDCARD_CHECK_R1_VALID()
87// This macro checks if the SD card response is valid
88// - x: SD card response
89// Returns 1 if valid and 0 otherwise
90///////////////////////////////////////////////////////////////////////////////
91#define SDCARD_CHECK_R1_VALID(x)    (~x & SDCARD_R1_RSP_VALID) ? 1 : 0
92
93///////////////////////////////////////////////////////////////////////////////
94//   SDCARD_CHECK_R1_ERROR()
95// This macro checks if there is an error in SD card response
96// - x: SD card response
97// Returns 1 if error and 0 otherwise
98///////////////////////////////////////////////////////////////////////////////
99#define SDCARD_CHECK_R1_ERROR(x)    ( x & 0x7E)                ? 1 : 0
100
101// SD card response 1 (R1) format constants
102#define SDCARD_R1_IN_IDLE_STATE     ( 1 << 0 ) // R1 bit 0
103#define SDCARD_R1_ERASE_RESET       ( 1 << 1 ) // R1 bit 1
104#define SDCARD_R1_ILLEGAL_CMD       ( 1 << 2 ) // R1 bit 2
105#define SDCARD_R1_COM_CRC_ERR       ( 1 << 3 ) // R1 bit 3
106#define SDCARD_R1_ERASE_SEQ_ERR     ( 1 << 4 ) // R1 bit 4
107#define SDCARD_R1_ADDRESS_ERR       ( 1 << 5 ) // R1 bit 5
108#define SDCARD_R1_PARAMETER_ERR     ( 1 << 6 ) // R1 bit 6
109#define SDCARD_R1_RSP_VALID         ( 1 << 7 ) // R1 bit 7
110
111#endif
112
113// Local Variables:
114// tab-width: 4
115// c-basic-offset: 4
116// c-file-offsets:((innamespace . 0)(inline-open . 0))
117// indent-tabs-mode: nil
118// End:
119// vim: filetype=c:expandtab:shiftwidth=4:tabstop=4:softtabstop=4
Note: See TracBrowser for help on using the repository browser.