/* * The authors hereby grant permission to use, copy, modify, distribute, * and license this software and its documentation for any purpose, provided * that existing copyright notices are retained in all copies and that this * notice is included verbatim in any distributions. No written agreement, * license, or royalty fee is required for any of the authorized uses. * Modifications to this software may be copyrighted by their authors * and need not follow the licensing terms described here, provided that * the new terms are clearly indicated on the first page of each file where * they apply. */ /* ** Copyright (C) 2008 Analog Devices Inc., All Rights Reserved. ** ************************************************************************************ ** ** This include file contains a list of macro "defines" to enable the programmer ** to use symbolic names for register-access and bit-manipulation. ** **/ #ifndef _DEF_BF518_H #define _DEF_BF518_H /* Include all Core registers and bit definitions */ #include /* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF518 */ /* Include defBF51x_base.h for the set of #defines that are common to all ADSP-BF51x processors */ #include #ifdef _MISRA_RULES #pragma diag(push) #pragma diag(suppress:misra_rule_19_4:"macros not strictly following 19.4") #pragma diag(suppress:misra_rule_19_7:"Allow function-like macros") #endif /* _MISRA_RULES */ /* The following are the #defines needed by ADSP-BF518 that are not in the common header */ /* 10/100 Ethernet Controller (0xFFC03000 - 0xFFC031FF) */ #define EMAC_OPMODE 0xFFC03000 /* Operating Mode Register */ #define EMAC_ADDRLO 0xFFC03004 /* Address Low (32 LSBs) Register */ #define EMAC_ADDRHI 0xFFC03008 /* Address High (16 MSBs) Register */ #define EMAC_HASHLO 0xFFC0300C /* Multicast Hash Table Low (Bins 31-0) Register */ #define EMAC_HASHHI 0xFFC03010 /* Multicast Hash Table High (Bins 63-32) Register */ #define EMAC_STAADD 0xFFC03014 /* Station Management Address Register */ #define EMAC_STADAT 0xFFC03018 /* Station Management Data Register */ #define EMAC_FLC 0xFFC0301C /* Flow Control Register */ #define EMAC_VLAN1 0xFFC03020 /* VLAN1 Tag Register */ #define EMAC_VLAN2 0xFFC03024 /* VLAN2 Tag Register */ #define EMAC_WKUP_CTL 0xFFC0302C /* Wake-Up Control/Status Register */ #define EMAC_WKUP_FFMSK0 0xFFC03030 /* Wake-Up Frame Filter 0 Byte Mask Register */ #define EMAC_WKUP_FFMSK1 0xFFC03034 /* Wake-Up Frame Filter 1 Byte Mask Register */ #define EMAC_WKUP_FFMSK2 0xFFC03038 /* Wake-Up Frame Filter 2 Byte Mask Register */ #define EMAC_WKUP_FFMSK3 0xFFC0303C /* Wake-Up Frame Filter 3 Byte Mask Register */ #define EMAC_WKUP_FFCMD 0xFFC03040 /* Wake-Up Frame Filter Commands Register */ #define EMAC_WKUP_FFOFF 0xFFC03044 /* Wake-Up Frame Filter Offsets Register */ #define EMAC_WKUP_FFCRC0 0xFFC03048 /* Wake-Up Frame Filter 0,1 CRC-16 Register */ #define EMAC_WKUP_FFCRC1 0xFFC0304C /* Wake-Up Frame Filter 2,3 CRC-16 Register */ #define EMAC_SYSCTL 0xFFC03060 /* EMAC System Control Register */ #define EMAC_SYSTAT 0xFFC03064 /* EMAC System Status Register */ #define EMAC_RX_STAT 0xFFC03068 /* RX Current Frame Status Register */ #define EMAC_RX_STKY 0xFFC0306C /* RX Sticky Frame Status Register */ #define EMAC_RX_IRQE 0xFFC03070 /* RX Frame Status Interrupt Enables Register */ #define EMAC_TX_STAT 0xFFC03074 /* TX Current Frame Status Register */ #define EMAC_TX_STKY 0xFFC03078 /* TX Sticky Frame Status Register */ #define EMAC_TX_IRQE 0xFFC0307C /* TX Frame Status Interrupt Enables Register */ #define EMAC_MMC_CTL 0xFFC03080 /* MMC Counter Control Register */ #define EMAC_MMC_RIRQS 0xFFC03084 /* MMC RX Interrupt Status Register */ #define EMAC_MMC_RIRQE 0xFFC03088 /* MMC RX Interrupt Enables Register */ #define EMAC_MMC_TIRQS 0xFFC0308C /* MMC TX Interrupt Status Register */ #define EMAC_MMC_TIRQE 0xFFC03090 /* MMC TX Interrupt Enables Register */ /* EMAC PTP (IEEE 1588) */ #define EMAC_PTP_CTL 0xffc030a0 /* PTP Block Control */ #define EMAC_PTP_IE 0xffc030a4 /* PTP Block Interrupt Enable */ #define EMAC_PTP_ISTAT 0xffc030a8 /* PTP Block Interrupt Status */ #define EMAC_PTP_FOFF 0xffc030ac /* PTP Filter offset Register */ #define EMAC_PTP_FV1 0xffc030b0 /* PTP Filter Value Register 1 */ #define EMAC_PTP_FV2 0xffc030b4 /* PTP Filter Value Register 2 */ #define EMAC_PTP_FV3 0xffc030b8 /* PTP Filter Value Register 3 */ #define EMAC_PTP_ADDEND 0xffc030bc /* PTP Addend for Frequency Compensation */ #define EMAC_PTP_ACCR 0xffc030c0 /* PTP Accumulator for Frequency Compensation */ #define EMAC_PTP_OFFSET 0xffc030c4 /* PTP Time Offset Register */ #define EMAC_PTP_TIMELO 0xffc030c8 /* PTP Precision Clock Time Low */ #define EMAC_PTP_TIMEHI 0xffc030cc /* PTP Precision Clock Time High */ #define EMAC_PTP_RXSNAPLO 0xffc030d0 /* PTP Receive Snapshot Register Low */ #define EMAC_PTP_RXSNAPHI 0xffc030d4 /* PTP Receive Snapshot Register High */ #define EMAC_PTP_TXSNAPLO 0xffc030d8 /* PTP Transmit Snapshot Register Low */ #define EMAC_PTP_TXSNAPHI 0xffc030dc /* PTP Transmit Snapshot Register High */ #define EMAC_PTP_ALARMLO 0xffc030e0 /* PTP Alarm time Low */ #define EMAC_PTP_ALARMHI 0xffc030e4 /* PTP Alarm time High */ #define EMAC_PTP_ID_OFF 0xffc030e8 /* PTP Capture ID offset register */ #define EMAC_PTP_ID_SNAP 0xffc030ec /* PTP Capture ID register */ #define EMAC_PTP_PPS_STARTLOP 0xffc030f0 /* PPS Start Time Low */ #define EMAC_PTP_PPS_STARTHIP 0xffc030f4 /* PPS Start Time High */ #define EMAC_PTP_PPS_PERIOD 0xffc030f8 /* PPS Count Register */ #define EMAC_RXC_OK 0xFFC03100 /* RX Frame Successful Count */ #define EMAC_RXC_FCS 0xFFC03104 /* RX Frame FCS Failure Count */ #define EMAC_RXC_ALIGN 0xFFC03108 /* RX Alignment Error Count */ #define EMAC_RXC_OCTET 0xFFC0310C /* RX Octets Successfully Received Count */ #define EMAC_RXC_DMAOVF 0xFFC03110 /* Internal MAC Sublayer Error RX Frame Count */ #define EMAC_RXC_UNICST 0xFFC03114 /* Unicast RX Frame Count */ #define EMAC_RXC_MULTI 0xFFC03118 /* Multicast RX Frame Count */ #define EMAC_RXC_BROAD 0xFFC0311C /* Broadcast RX Frame Count */ #define EMAC_RXC_LNERRI 0xFFC03120 /* RX Frame In Range Error Count */ #define EMAC_RXC_LNERRO 0xFFC03124 /* RX Frame Out Of Range Error Count */ #define EMAC_RXC_LONG 0xFFC03128 /* RX Frame Too Long Count */ #define EMAC_RXC_MACCTL 0xFFC0312C /* MAC Control RX Frame Count */ #define EMAC_RXC_OPCODE 0xFFC03130 /* Unsupported Op-Code RX Frame Count */ #define EMAC_RXC_PAUSE 0xFFC03134 /* MAC Control Pause RX Frame Count */ #define EMAC_RXC_ALLFRM 0xFFC03138 /* Overall RX Frame Count */ #define EMAC_RXC_ALLOCT 0xFFC0313C /* Overall RX Octet Count */ #define EMAC_RXC_TYPED 0xFFC03140 /* Type/Length Consistent RX Frame Count */ #define EMAC_RXC_SHORT 0xFFC03144 /* RX Frame Fragment Count - Byte Count x < 64 */ #define EMAC_RXC_EQ64 0xFFC03148 /* Good RX Frame Count - Byte Count x = 64 */ #define EMAC_RXC_LT128 0xFFC0314C /* Good RX Frame Count - Byte Count 64 < x < 128 */ #define EMAC_RXC_LT256 0xFFC03150 /* Good RX Frame Count - Byte Count 128 <= x < 256 */ #define EMAC_RXC_LT512 0xFFC03154 /* Good RX Frame Count - Byte Count 256 <= x < 512 */ #define EMAC_RXC_LT1024 0xFFC03158 /* Good RX Frame Count - Byte Count 512 <= x < 1024 */ #define EMAC_RXC_GE1024 0xFFC0315C /* Good RX Frame Count - Byte Count x >= 1024 */ #define EMAC_TXC_OK 0xFFC03180 /* TX Frame Successful Count */ #define EMAC_TXC_1COL 0xFFC03184 /* TX Frames Successful After Single Collision Count */ #define EMAC_TXC_GT1COL 0xFFC03188 /* TX Frames Successful After Multiple Collisions Count */ #define EMAC_TXC_OCTET 0xFFC0318C /* TX Octets Successfully Received Count */ #define EMAC_TXC_DEFER 0xFFC03190 /* TX Frame Delayed Due To Busy Count */ #define EMAC_TXC_LATECL 0xFFC03194 /* Late TX Collisions Count */ #define EMAC_TXC_XS_COL 0xFFC03198 /* TX Frame Failed Due To Excessive Collisions Count */ #define EMAC_TXC_DMAUND 0xFFC0319C /* Internal MAC Sublayer Error TX Frame Count */ #define EMAC_TXC_CRSERR 0xFFC031A0 /* Carrier Sense Deasserted During TX Frame Count */ #define EMAC_TXC_UNICST 0xFFC031A4 /* Unicast TX Frame Count */ #define EMAC_TXC_MULTI 0xFFC031A8 /* Multicast TX Frame Count */ #define EMAC_TXC_BROAD 0xFFC031AC /* Broadcast TX Frame Count */ #define EMAC_TXC_XS_DFR 0xFFC031B0 /* TX Frames With Excessive Deferral Count */ #define EMAC_TXC_MACCTL 0xFFC031B4 /* MAC Control TX Frame Count */ #define EMAC_TXC_ALLFRM 0xFFC031B8 /* Overall TX Frame Count */ #define EMAC_TXC_ALLOCT 0xFFC031BC /* Overall TX Octet Count */ #define EMAC_TXC_EQ64 0xFFC031C0 /* Good TX Frame Count - Byte Count x = 64 */ #define EMAC_TXC_LT128 0xFFC031C4 /* Good TX Frame Count - Byte Count 64 < x < 128 */ #define EMAC_TXC_LT256 0xFFC031C8 /* Good TX Frame Count - Byte Count 128 <= x < 256 */ #define EMAC_TXC_LT512 0xFFC031CC /* Good TX Frame Count - Byte Count 256 <= x < 512 */ #define EMAC_TXC_LT1024 0xFFC031D0 /* Good TX Frame Count - Byte Count 512 <= x < 1024 */ #define EMAC_TXC_GE1024 0xFFC031D4 /* Good TX Frame Count - Byte Count x >= 1024 */ #define EMAC_TXC_ABORT 0xFFC031D8 /* Total TX Frames Aborted Count */ /* Listing for IEEE-Supported Count Registers */ #define FramesReceivedOK EMAC_RXC_OK /* RX Frame Successful Count */ #define FrameCheckSequenceErrors EMAC_RXC_FCS /* RX Frame FCS Failure Count */ #define AlignmentErrors EMAC_RXC_ALIGN /* RX Alignment Error Count */ #define OctetsReceivedOK EMAC_RXC_OCTET /* RX Octets Successfully Received Count */ #define FramesLostDueToIntMACRcvError EMAC_RXC_DMAOVF /* Internal MAC Sublayer Error RX Frame Count */ #define UnicastFramesReceivedOK EMAC_RXC_UNICST /* Unicast RX Frame Count */ #define MulticastFramesReceivedOK EMAC_RXC_MULTI /* Multicast RX Frame Count */ #define BroadcastFramesReceivedOK EMAC_RXC_BROAD /* Broadcast RX Frame Count */ #define InRangeLengthErrors EMAC_RXC_LNERRI /* RX Frame In Range Error Count */ #define OutOfRangeLengthField EMAC_RXC_LNERRO /* RX Frame Out Of Range Error Count */ #define FrameTooLongErrors EMAC_RXC_LONG /* RX Frame Too Long Count */ #define MACControlFramesReceived EMAC_RXC_MACCTL /* MAC Control RX Frame Count */ #define UnsupportedOpcodesReceived EMAC_RXC_OPCODE /* Unsupported Op-Code RX Frame Count */ #define PAUSEMACCtrlFramesReceived EMAC_RXC_PAUSE /* MAC Control Pause RX Frame Count */ #define FramesReceivedAll EMAC_RXC_ALLFRM /* Overall RX Frame Count */ #define OctetsReceivedAll EMAC_RXC_ALLOCT /* Overall RX Octet Count */ #define TypedFramesReceived EMAC_RXC_TYPED /* Type/Length Consistent RX Frame Count */ #define FramesLenLt64Received EMAC_RXC_SHORT /* RX Frame Fragment Count - Byte Count x < 64 */ #define FramesLenEq64Received EMAC_RXC_EQ64 /* Good RX Frame Count - Byte Count x = 64 */ #define FramesLen65_127Received EMAC_RXC_LT128 /* Good RX Frame Count - Byte Count 64 < x < 128 */ #define FramesLen128_255Received EMAC_RXC_LT256 /* Good RX Frame Count - Byte Count 128 <= x < 256 */ #define FramesLen256_511Received EMAC_RXC_LT512 /* Good RX Frame Count - Byte Count 256 <= x < 512 */ #define FramesLen512_1023Received EMAC_RXC_LT1024 /* Good RX Frame Count - Byte Count 512 <= x < 1024 */ #define FramesLen1024_MaxReceived EMAC_RXC_GE1024 /* Good RX Frame Count - Byte Count x >= 1024 */ #define FramesTransmittedOK EMAC_TXC_OK /* TX Frame Successful Count */ #define SingleCollisionFrames EMAC_TXC_1COL /* TX Frames Successful After Single Collision Count */ #define MultipleCollisionFrames EMAC_TXC_GT1COL /* TX Frames Successful After Multiple Collisions Count */ #define OctetsTransmittedOK EMAC_TXC_OCTET /* TX Octets Successfully Received Count */ #define FramesWithDeferredXmissions EMAC_TXC_DEFER /* TX Frame Delayed Due To Busy Count */ #define LateCollisions EMAC_TXC_LATECL /* Late TX Collisions Count */ #define FramesAbortedDueToXSColls EMAC_TXC_XS_COL /* TX Frame Failed Due To Excessive Collisions Count */ #define FramesLostDueToIntMacXmitError EMAC_TXC_DMAUND /* Internal MAC Sublayer Error TX Frame Count */ #define CarrierSenseErrors EMAC_TXC_CRSERR /* Carrier Sense Deasserted During TX Frame Count */ #define UnicastFramesXmittedOK EMAC_TXC_UNICST /* Unicast TX Frame Count */ #define MulticastFramesXmittedOK EMAC_TXC_MULTI /* Multicast TX Frame Count */ #define BroadcastFramesXmittedOK EMAC_TXC_BROAD /* Broadcast TX Frame Count */ #define FramesWithExcessiveDeferral EMAC_TXC_XS_DFR /* TX Frames With Excessive Deferral Count */ #define MACControlFramesTransmitted EMAC_TXC_MACCTL /* MAC Control TX Frame Count */ #define FramesTransmittedAll EMAC_TXC_ALLFRM /* Overall TX Frame Count */ #define OctetsTransmittedAll EMAC_TXC_ALLOCT /* Overall TX Octet Count */ #define FramesLenEq64Transmitted EMAC_TXC_EQ64 /* Good TX Frame Count - Byte Count x = 64 */ #define FramesLen65_127Transmitted EMAC_TXC_LT128 /* Good TX Frame Count - Byte Count 64 < x < 128 */ #define FramesLen128_255Transmitted EMAC_TXC_LT256 /* Good TX Frame Count - Byte Count 128 <= x < 256 */ #define FramesLen256_511Transmitted EMAC_TXC_LT512 /* Good TX Frame Count - Byte Count 256 <= x < 512 */ #define FramesLen512_1023Transmitted EMAC_TXC_LT1024 /* Good TX Frame Count - Byte Count 512 <= x < 1024 */ #define FramesLen1024_MaxTransmitted EMAC_TXC_GE1024 /* Good TX Frame Count - Byte Count x >= 1024 */ #define TxAbortedFrames EMAC_TXC_ABORT /* Total TX Frames Aborted Count */ /* RSI Registers */ #define RSI_PWR_CONTROL 0xFFC03800 /* RSI Power Control Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_PWR_CTL RSI_PWR_CONTROL /* SDH Power Control */ #define RSI_CLK_CONTROL 0xFFC03804 /* RSI Clock Control Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_CLK_CTL RSI_CLK_CONTROL /* SDH Clock Control */ #define RSI_ARGUMENT 0xFFC03808 /* RSI Argument Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_ARGUMENT RSI_ARGUMENT /* SDH Argument */ #define RSI_COMMAND 0xFFC0380C /* RSI Command Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_COMMAND RSI_COMMAND /* SDH Command */ #define RSI_RESP_CMD 0xFFC03810 /* RSI Response Command Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_RESP_CMD RSI_RESP_CMD /* SDH Response Command */ #define RSI_RESPONSE0 0xFFC03814 /* RSI Response Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_RESPONSE0 RSI_RESPONSE0 /* SDH Response0 */ #define RSI_RESPONSE1 0xFFC03818 /* RSI Response Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_RESPONSE1 RSI_RESPONSE1 /* SDH Response1 */ #define RSI_RESPONSE2 0xFFC0381C /* RSI Response Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_RESPONSE2 RSI_RESPONSE2 /* SDH Response2 */ #define RSI_RESPONSE3 0xFFC03820 /* RSI Response Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_RESPONSE3 RSI_RESPONSE3 /* SDH Response3 */ #define RSI_DATA_TIMER 0xFFC03824 /* RSI Data Timer Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_DATA_TIMER RSI_DATA_TIMER /* SDH Data Timer */ #define RSI_DATA_LGTH 0xFFC03828 /* RSI Data Length Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_DATA_LGTH RSI_DATA_LGTH /* SDH Data Length */ #define RSI_DATA_CONTROL 0xFFC0382C /* RSI Data Control Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_DATA_CTL RSI_DATA_CONTROL /* SDH Data Control */ #define RSI_DATA_CNT 0xFFC03830 /* RSI Data Counter Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_DATA_CNT RSI_DATA_CNT /* SDH Data Counter */ #define RSI_STATUS 0xFFC03834 /* RSI Status Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_STATUS RSI_STATUS /* SDH Status */ #define RSI_STATUSCL 0xFFC03838 /* RSI Status Clear Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_STATUS_CLR RSI_STATUSCL /* SDH Status Clear */ #define RSI_MASK0 0xFFC0383C /* RSI Interrupt 0 Mask Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_MASK0 RSI_MASK0 /* SDH Interrupt0 Mask */ #define RSI_MASK1 0xFFC03840 /* RSI Interrupt 1 Mask Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_MASK1 RSI_MASK1 /* SDH Interrupt1 Mask */ #define RSI_FIFO_CNT 0xFFC03848 /* RSI FIFO Counter Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_FIFO_CNT RSI_FIFO_CNT /* SDH FIFO Counter */ #define RSI_CEATA_CONTROL 0xFFC0384C /* RSI CEATA Register */ #define RSI_FIFO 0xFFC03880 /* RSI Data FIFO Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_FIFO RSI_FIFO /* SDH Data FIFO */ #define RSI_ESTAT 0xFFC038C0 /* RSI Exception Status Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_E_STATUS RSI_ESTAT /* SDH Exception Status */ #define RSI_EMASK 0xFFC038C4 /* RSI Exception Mask Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_E_MASK RSI_EMASK /* SDH Exception Mask */ #define RSI_CONFIG 0xFFC038C8 /* RSI Configuration Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_CFG RSI_CONFIG /* SDH Configuration */ #define RSI_RD_WAIT_EN 0xFFC038CC /* RSI Read Wait Enable Register */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_RD_WAIT_EN RSI_RD_WAIT_EN /* SDH Read Wait Enable */ #define RSI_PID0 0xFFC038D0 /* RSI Peripheral ID Register 0 */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_PID0 RSI_PID0 /* SDH Peripheral Identification0 */ #define RSI_PID1 0xFFC038D4 /* RSI Peripheral ID Register 1 */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_PID1 RSI_PID1 /* SDH Peripheral Identification1 */ #define RSI_PID2 0xFFC038D8 /* RSI Peripheral ID Register 2 */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_PID2 RSI_PID2 /* SDH Peripheral Identification2 */ #define RSI_PID3 0xFFC038DC /* RSI Peripheral ID Register 3 */ /* legacy register name (below) provided for backwards code compatibility */ #define SDH_PID3 RSI_PID3 /* SDH Peripheral Identification3 */ /* RSI Registers */ /*********************************************************************************** ** System MMR Register Bits And Macros ** ** Disclaimer: All macros are intended to make C and Assembly code more readable. ** Use these macros carefully, as any that do left shifts for field ** depositing will result in the lower order bits being destroyed. Any ** macro that shifts left to properly position the bit-field should be ** used as part of an OR to initialize a register and NOT as a dynamic ** modifier UNLESS the lower order bits are saved and ORed back in when ** the macro is used. *************************************************************************************/ /************************ ETHERNET 10/100 CONTROLLER MASKS ************************/ /* EMAC_OPMODE Masks */ #define RE 0x00000001 /* Receiver Enable */ #define ASTP 0x00000002 /* Enable Automatic Pad Stripping On RX Frames */ #define HU 0x00000010 /* Hash Filter Unicast Address */ #define HM 0x00000020 /* Hash Filter Multicast Address */ #define PAM 0x00000040 /* Pass-All-Multicast Mode Enable */ #define PR 0x00000080 /* Promiscuous Mode Enable */ #define IFE 0x00000100 /* Inverse Filtering Enable */ #define DBF 0x00000200 /* Disable Broadcast Frame Reception */ #define PBF 0x00000400 /* Pass Bad Frames Enable */ #define PSF 0x00000800 /* Pass Short Frames Enable */ #define RAF 0x00001000 /* Receive-All Mode */ #define TE 0x00010000 /* Transmitter Enable */ #define DTXPAD 0x00020000 /* Disable Automatic TX Padding */ #define DTXCRC 0x00040000 /* Disable Automatic TX CRC Generation */ #define DC 0x00080000 /* Deferral Check */ #define BOLMT 0x00300000 /* Back-Off Limit */ #define BOLMT_10 0x00000000 /* 10-bit range */ #define BOLMT_8 0x00100000 /* 8-bit range */ #define BOLMT_4 0x00200000 /* 4-bit range */ #define BOLMT_1 0x00300000 /* 1-bit range */ #define DRTY 0x00400000 /* Disable TX Retry On Collision */ #define LCTRE 0x00800000 /* Enable TX Retry On Late Collision */ #define RMII 0x01000000 /* RMII/MII* Mode */ #define RMII_10 0x02000000 /* Speed Select for RMII Port (10MBit/100MBit*) */ #define FDMODE 0x04000000 /* Duplex Mode Enable (Full/Half*) */ #define LB 0x08000000 /* Internal Loopback Enable */ #define DRO 0x10000000 /* Disable Receive Own Frames (Half-Duplex Mode) */ /* EMAC_STAADD Masks */ #define STABUSY 0x00000001 /* Initiate Station Mgt Reg Access / STA Busy Stat */ #define STAOP 0x00000002 /* Station Management Operation Code (Write/Read*) */ #define STADISPRE 0x00000004 /* Disable Preamble Generation */ #define STAIE 0x00000008 /* Station Mgt. Transfer Done Interrupt Enable */ #define REGAD 0x000007C0 /* STA Register Address */ #define PHYAD 0x0000F800 /* PHY Device Address */ #ifdef _MISRA_RULES #define SET_REGAD(x) (((x)&0x1Fu)<< 6 ) /* Set STA Register Address */ #define SET_PHYAD(x) (((x)&0x1Fu)<< 11 ) /* Set PHY Device Address */ #else #define SET_REGAD(x) (((x)&0x1F)<< 6 ) /* Set STA Register Address */ #define SET_PHYAD(x) (((x)&0x1F)<< 11 ) /* Set PHY Device Address */ #endif /* _MISRA_RULES */ /* EMAC_STADAT Mask */ #define STADATA 0x0000FFFF /* Station Management Data */ /* EMAC_FLC Masks */ #define FLCBUSY 0x00000001 /* Send Flow Ctrl Frame / Flow Ctrl Busy Status */ #define FLCE 0x00000002 /* Flow Control Enable */ #define PCF 0x00000004 /* Pass Control Frames */ #define BKPRSEN 0x00000008 /* Enable Backpressure */ #define FLCPAUSE 0xFFFF0000 /* Pause Time */ #ifdef _MISRA_RULES #define SET_FLCPAUSE(x) (((x)&0xFFFFu)<< 16) /* Set Pause Time */ #else #define SET_FLCPAUSE(x) (((x)&0xFFFF)<< 16) /* Set Pause Time */ #endif /* _MISRA_RULES */ /* EMAC_WKUP_CTL Masks */ #define CAPWKFRM 0x00000001 /* Capture Wake-Up Frames */ #define MPKE 0x00000002 /* Magic Packet Enable */ #define RWKE 0x00000004 /* Remote Wake-Up Frame Enable */ #define GUWKE 0x00000008 /* Global Unicast Wake Enable */ #define MPKS 0x00000020 /* Magic Packet Received Status */ #define RWKS 0x00000F00 /* Wake-Up Frame Received Status, Filters 3:0 */ /* EMAC_WKUP_FFCMD Masks */ #define WF0_E 0x00000001 /* Enable Wake-Up Filter 0 */ #define WF0_T 0x00000008 /* Wake-Up Filter 0 Addr Type (Multicast/Unicast*) */ #define WF1_E 0x00000100 /* Enable Wake-Up Filter 1 */ #define WF1_T 0x00000800 /* Wake-Up Filter 1 Addr Type (Multicast/Unicast*) */ #define WF2_E 0x00010000 /* Enable Wake-Up Filter 2 */ #define WF2_T 0x00080000 /* Wake-Up Filter 2 Addr Type (Multicast/Unicast*) */ #define WF3_E 0x01000000 /* Enable Wake-Up Filter 3 */ #define WF3_T 0x08000000 /* Wake-Up Filter 3 Addr Type (Multicast/Unicast*) */ /* EMAC_WKUP_FFOFF Masks */ #define WF0_OFF 0x000000FF /* Wake-Up Filter 0 Pattern Offset */ #define WF1_OFF 0x0000FF00 /* Wake-Up Filter 1 Pattern Offset */ #define WF2_OFF 0x00FF0000 /* Wake-Up Filter 2 Pattern Offset */ #define WF3_OFF 0xFF000000 /* Wake-Up Filter 3 Pattern Offset */ #ifdef _MISRA_RULES #define SET_WF0_OFF(x) (((x)&0xFFu)<< 0 ) /* Set Wake-Up Filter 0 Byte Offset */ #define SET_WF1_OFF(x) (((x)&0xFFu)<< 8 ) /* Set Wake-Up Filter 1 Byte Offset */ #define SET_WF2_OFF(x) (((x)&0xFFu)<< 16 ) /* Set Wake-Up Filter 2 Byte Offset */ #define SET_WF3_OFF(x) (((x)&0xFFu)<< 24 ) /* Set Wake-Up Filter 3 Byte Offset */ #else #define SET_WF0_OFF(x) (((x)&0xFF)<< 0 ) /* Set Wake-Up Filter 0 Byte Offset */ #define SET_WF1_OFF(x) (((x)&0xFF)<< 8 ) /* Set Wake-Up Filter 1 Byte Offset */ #define SET_WF2_OFF(x) (((x)&0xFF)<< 16 ) /* Set Wake-Up Filter 2 Byte Offset */ #define SET_WF3_OFF(x) (((x)&0xFF)<< 24 ) /* Set Wake-Up Filter 3 Byte Offset */ #endif /* _MISRA_RULES */ /* Set ALL Offsets */ #define SET_WF_OFFS(x0,x1,x2,x3) (SET_WF0_OFF((x0))|SET_WF1_OFF((x1))|SET_WF2_OFF((x2))|SET_WF3_OFF((x3))) /* EMAC_WKUP_FFCRC0 Masks */ #define WF0_CRC 0x0000FFFF /* Wake-Up Filter 0 Pattern CRC */ #define WF1_CRC 0xFFFF0000 /* Wake-Up Filter 1 Pattern CRC */ #ifdef _MISRA_RULES #define SET_WF0_CRC(x) (((x)&0xFFFFu)<< 0 ) /* Set Wake-Up Filter 0 Target CRC */ #define SET_WF1_CRC(x) (((x)&0xFFFFu)<< 16 ) /* Set Wake-Up Filter 1 Target CRC */ #else #define SET_WF0_CRC(x) (((x)&0xFFFF)<< 0 ) /* Set Wake-Up Filter 0 Target CRC */ #define SET_WF1_CRC(x) (((x)&0xFFFF)<< 16 ) /* Set Wake-Up Filter 1 Target CRC */ #endif /* _MISRA_RULES */ /* EMAC_WKUP_FFCRC1 Masks */ #define WF2_CRC 0x0000FFFF /* Wake-Up Filter 2 Pattern CRC */ #define WF3_CRC 0xFFFF0000 /* Wake-Up Filter 3 Pattern CRC */ #ifdef _MISRA_RULES #define SET_WF2_CRC(x) (((x)&0xFFFFu)<< 0 ) /* Set Wake-Up Filter 2 Target CRC */ #define SET_WF3_CRC(x) (((x)&0xFFFFu)<< 16 ) /* Set Wake-Up Filter 3 Target CRC */ #else #define SET_WF2_CRC(x) (((x)&0xFFFF)<< 0 ) /* Set Wake-Up Filter 2 Target CRC */ #define SET_WF3_CRC(x) (((x)&0xFFFF)<< 16 ) /* Set Wake-Up Filter 3 Target CRC */ #endif /* _MISRA_RULES */ /* EMAC_SYSCTL Masks */ #define PHYIE 0x00000001 /* PHY_INT Interrupt Enable */ #define RXDWA 0x00000002 /* Receive Frame DMA Word Alignment (Odd/Even*) */ #define RXCKS 0x00000004 /* Enable RX Frame TCP/UDP Checksum Computation */ #define MDCDIV 0x00003F00 /* SCLK:MDC Clock Divisor [MDC=SCLK/(2*(N+1))] */ #ifdef _MISRA_RULES #define SET_MDCDIV(x) (((x)&0x3Fu)<< 8) /* Set MDC Clock Divisor */ #else #define SET_MDCDIV(x) (((x)&0x3F)<< 8) /* Set MDC Clock Divisor */ #endif /* _MISRA_RULES */ /* EMAC_SYSTAT Masks */ #define PHYINT 0x00000001 /* PHY_INT Interrupt Status */ #define MMCINT 0x00000002 /* MMC Counter Interrupt Status */ #define RXFSINT 0x00000004 /* RX Frame-Status Interrupt Status */ #define TXFSINT 0x00000008 /* TX Frame-Status Interrupt Status */ #define WAKEDET 0x00000010 /* Wake-Up Detected Status */ #define RXDMAERR 0x00000020 /* RX DMA Direction Error Status */ #define TXDMAERR 0x00000040 /* TX DMA Direction Error Status */ #define STMDONE 0x00000080 /* Station Mgt. Transfer Done Interrupt Status */ /* EMAC_RX_STAT, EMAC_RX_STKY, and EMAC_RX_IRQE Masks */ #define RX_FRLEN 0x000007FF /* Frame Length In Bytes */ #define RX_COMP 0x00001000 /* RX Frame Complete */ #define RX_OK 0x00002000 /* RX Frame Received With No Errors */ #define RX_LONG 0x00004000 /* RX Frame Too Long Error */ #define RX_ALIGN 0x00008000 /* RX Frame Alignment Error */ #define RX_CRC 0x00010000 /* RX Frame CRC Error */ #define RX_LEN 0x00020000 /* RX Frame Length Error */ #define RX_FRAG 0x00040000 /* RX Frame Fragment Error */ #define RX_ADDR 0x00080000 /* RX Frame Address Filter Failed Error */ #define RX_DMAO 0x00100000 /* RX Frame DMA Overrun Error */ #define RX_PHY 0x00200000 /* RX Frame PHY Error */ #define RX_LATE 0x00400000 /* RX Frame Late Collision Error */ #define RX_RANGE 0x00800000 /* RX Frame Length Field Out of Range Error */ #define RX_MULTI 0x01000000 /* RX Multicast Frame Indicator */ #define RX_BROAD 0x02000000 /* RX Broadcast Frame Indicator */ #define RX_CTL 0x04000000 /* RX Control Frame Indicator */ #define RX_UCTL 0x08000000 /* Unsupported RX Control Frame Indicator */ #define RX_TYPE 0x10000000 /* RX Typed Frame Indicator */ #define RX_VLAN1 0x20000000 /* RX VLAN1 Frame Indicator */ #define RX_VLAN2 0x40000000 /* RX VLAN2 Frame Indicator */ #define RX_ACCEPT 0x80000000 /* RX Frame Accepted Indicator */ /* EMAC_TX_STAT, EMAC_TX_STKY, and EMAC_TX_IRQE Masks */ #define TX_COMP 0x00000001 /* TX Frame Complete */ #define TX_OK 0x00000002 /* TX Frame Sent With No Errors */ #define TX_ECOLL 0x00000004 /* TX Frame Excessive Collision Error */ #define TX_LATE 0x00000008 /* TX Frame Late Collision Error */ #define TX_DMAU 0x00000010 /* TX Frame DMA Underrun Error (STAT) */ #define TX_MACE 0x00000010 /* Internal MAC Error Detected (STKY and IRQE) */ #define TX_EDEFER 0x00000020 /* TX Frame Excessive Deferral Error */ #define TX_BROAD 0x00000040 /* TX Broadcast Frame Indicator */ #define TX_MULTI 0x00000080 /* TX Multicast Frame Indicator */ #define TX_CCNT 0x00000F00 /* TX Frame Collision Count */ #define TX_DEFER 0x00001000 /* TX Frame Deferred Indicator */ #define TX_CRS 0x00002000 /* TX Frame Carrier Sense Not Asserted Error */ #define TX_LOSS 0x00004000 /* TX Frame Carrier Lost During TX Error */ #define TX_RETRY 0x00008000 /* TX Frame Successful After Retry */ #define TX_FRLEN 0x07FF0000 /* TX Frame Length (Bytes) */ /* EMAC_MMC_CTL Masks */ #define RSTC 0x00000001 /* Reset All Counters */ #define CROLL 0x00000002 /* Counter Roll-Over Enable */ #define CCOR 0x00000004 /* Counter Clear-On-Read Mode Enable */ #define MMCE 0x00000008 /* Enable MMC Counter Operation */ /* EMAC_MMC_RIRQS and EMAC_MMC_RIRQE Masks */ #define RX_OK_CNT 0x00000001 /* RX Frames Received With No Errors */ #define RX_FCS_CNT 0x00000002 /* RX Frames W/Frame Check Sequence Errors */ #define RX_ALIGN_CNT 0x00000004 /* RX Frames With Alignment Errors */ #define RX_OCTET_CNT 0x00000008 /* RX Octets Received OK */ #define RX_LOST_CNT 0x00000010 /* RX Frames Lost Due To Internal MAC RX Error */ #define RX_UNI_CNT 0x00000020 /* Unicast RX Frames Received OK */ #define RX_MULTI_CNT 0x00000040 /* Multicast RX Frames Received OK */ #define RX_BROAD_CNT 0x00000080 /* Broadcast RX Frames Received OK */ #define RX_IRL_CNT 0x00000100 /* RX Frames With In-Range Length Errors */ #define RX_ORL_CNT 0x00000200 /* RX Frames With Out-Of-Range Length Errors */ #define RX_LONG_CNT 0x00000400 /* RX Frames With Frame Too Long Errors */ #define RX_MACCTL_CNT 0x00000800 /* MAC Control RX Frames Received */ #define RX_OPCODE_CTL 0x00001000 /* Unsupported Op-Code RX Frames Received */ #define RX_PAUSE_CNT 0x00002000 /* PAUSEMAC Control RX Frames Received */ #define RX_ALLF_CNT 0x00004000 /* All RX Frames Received */ #define RX_ALLO_CNT 0x00008000 /* All RX Octets Received */ #define RX_TYPED_CNT 0x00010000 /* Typed RX Frames Received */ #define RX_SHORT_CNT 0x00020000 /* RX Frame Fragments (< 64 Bytes) Received */ #define RX_EQ64_CNT 0x00040000 /* 64-Byte RX Frames Received */ #define RX_LT128_CNT 0x00080000 /* 65-127-Byte RX Frames Received */ #define RX_LT256_CNT 0x00100000 /* 128-255-Byte RX Frames Received */ #define RX_LT512_CNT 0x00200000 /* 256-511-Byte RX Frames Received */ #define RX_LT1024_CNT 0x00400000 /* 512-1023-Byte RX Frames Received */ #define RX_GE1024_CNT 0x00800000 /* 1024-Max-Byte RX Frames Received */ /* EMAC_MMC_TIRQS and EMAC_MMC_TIRQE Masks */ #define TX_OK_CNT 0x00000001 /* TX Frames Sent OK */ #define TX_SCOLL_CNT 0x00000002 /* TX Frames With Single Collisions */ #define TX_MCOLL_CNT 0x00000004 /* TX Frames With Multiple Collisions */ #define TX_OCTET_CNT 0x00000008 /* TX Octets Sent OK */ #define TX_DEFER_CNT 0x00000010 /* TX Frames With Deferred Transmission */ #define TX_LATE_CNT 0x00000020 /* TX Frames With Late Collisions */ #define TX_ABORTC_CNT 0x00000040 /* TX Frames Aborted Due To Excess Collisions */ #define TX_LOST_CNT 0x00000080 /* TX Frames Lost Due To Internal MAC TX Error */ #define TX_CRS_CNT 0x00000100 /* TX Frames With Carrier Sense Errors */ #define TX_UNI_CNT 0x00000200 /* Unicast TX Frames Sent */ #define TX_MULTI_CNT 0x00000400 /* Multicast TX Frames Sent */ #define TX_BROAD_CNT 0x00000800 /* Broadcast TX Frames Sent */ #define TX_EXDEF_CTL 0x00001000 /* TX Frames With Excessive Deferral */ #define TX_MACCTL_CNT 0x00002000 /* MAC Control TX Frames Sent */ #define TX_ALLF_CNT 0x00004000 /* All TX Frames Sent */ #define TX_ALLO_CNT 0x00008000 /* All TX Octets Sent */ #define TX_EQ64_CNT 0x00010000 /* 64-Byte TX Frames Sent */ #define TX_LT128_CNT 0x00020000 /* 65-127-Byte TX Frames Sent */ #define TX_LT256_CNT 0x00040000 /* 128-255-Byte TX Frames Sent */ #define TX_LT512_CNT 0x00080000 /* 256-511-Byte TX Frames Sent */ #define TX_LT1024_CNT 0x00100000 /* 512-1023-Byte TX Frames Sent */ #define TX_GE1024_CNT 0x00200000 /* 1024-Max-Byte TX Frames Sent */ #define TX_ABORT_CNT 0x00400000 /* TX Frames Aborted */ /* Bit masks for EMAC_PTP_CTL */ #define EMAC_PTP_CTL_EN 0x1 /* Block Enable */ #define EMAC_PTP_CTL_TL 0x2 /* Time Stamp Lock */ #define EMAC_PTP_CTL_CKS 0xC /* Clock source for the PTP_TSYNC block */ #define EMAC_PTP_CTL_ASEN 0x10 /* Auxiliary Snapshot Enable */ #define EMAC_PTP_CTL_CKDIV 0x60 /* Divider for the selected PTP_CLK output */ #define EMAC_PTP_CTL_PPSEN 0x80 /* Pulse Per Second (PPS) Enable */ #define EMAC_PTP_CTL_EFTM 0x100 /* Ethernet Frame type field compare mask */ #define EMAC_PTP_CTL_IPVM 0x200 /* IP Version field compare mask */ #define EMAC_PTP_CTL_IPTM 0x400 /* IP Type Frame field (Layer 4 protocol) compare mask */ #define EMAC_PTP_CTL_UDPEM 0x800 /* UDP Event port field compare mask */ #define EMAC_PTP_CTL_PTPCM 0x1000 /* PTP Control field compare mask */ #define EMAC_PTP_CTL_CKOEN 0x2000 /* Clock output Enable */ /* Bit masks for EMAC_PTP_IE */ #define EMAC_PTP_IE_ALIE 0x1 /* Alarm Feature and Interrupt Enable */ #define EMAC_PTP_IE_RXEIE 0x2 /* Receive Event Interrupt Enable */ #define EMAC_PTP_IE_RXGIE 0x4 /* Receive General Interrupt Enable */ #define EMAC_PTP_IE_TXIE 0x8 /* Transmit Interrupt Enable */ #define EMAC_PTP_IE_TXOVE 0x10 /* Transmit Overrun Error Interrupt Enable */ #define EMAC_PTP_IE_RXOVE 0x20 /* Receive Overrun Error Interrupt Enable */ #define EMAC_PTP_IE_ASIE 0x40 /* Auxiliary Snapshot Interrupt Enable */ /* Bit masks for EMAC_PTP_ISTAT */ #define EMAC_PTP_ISTAT_ALS 0x1 /* Alarm Status */ #define EMAC_PTP_ISTAT_RXEL 0x2 /* Receive Event Interrupt Locked */ #define EMAC_PTP_ISTAT_RXGL 0x4 /* Receive General Interrupt Locked */ #define EMAC_PTP_ISTAT_TXTL 0x8 /* Transmit Snapshot Locked */ #define EMAC_PTP_ISTAT_RXOV 0x10 /* Receive Snapshot Overrun Status */ #define EMAC_PTP_ISTAT_TXOV 0x20 /* Transmit snapshot Overrun Status */ #define EMAC_PTP_ISTAT_ASL 0x40 /* Auxiliary Snapshot Interrupt Status */ /* Bit masks for RSI_PWR_CONTROL */ #define PWR_ON 0x3 /* Power On */ #define RSI_CMD_OD 0x40 /* Open Drain Output */ /* legacy bit mask (below) provided for backwards code compatibility */ #define SD_CMD_OD RSI_CMD_OD /* Open Drain Output */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nSD_CMD_OD 0x0 /* legacy bit mask (below) provided for backwards code compatibility */ #if 0 #define TBD 0x3c /* TBD */ #endif /* legacy bit mask (below) provided for backwards code compatibility */ #define ROD_CTL 0x80 /* legacy bit mask (below) provided for backwards code compatibility */ #define nROD_CTL 0x80 /* Bit masks for RSI_CLK_CONTROL */ #define CLKDIV 0xff /* MC_CLK Divisor */ #define CLK_EN 0x100 /* MC_CLK Bus Clock Enable */ /* legacy bit mask (below) provided for backwards code compatibility */ #define CLK_E CLK_EN /* MC_CLK Bus Clock Enable */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCLK_E 0x0 #define PWR_SV_EN 0x200 /* Power Save Enable */ /* legacy bit mask (below) provided for backwards code compatibility */ #define PWR_SV_E PWR_SV_EN /* Power Save Enable */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nPWR_SV_E 0x0 #define CLKDIV_BYPASS 0x400 /* Bypass Divisor */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCLKDIV_BYPASS 0x0 #define BUS_MODE 0x1800 /* Bus width selection */ /* legacy bit mask (below) provided for backwards code compatibility */ #define WIDE_BUS 0x0800 /* Wide Bus Mode Enable */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nWIDE_BUS 0x0 /* Bit masks for RSI_COMMAND */ #define CMD_IDX 0x3f /* Command Index */ #define CMD_RSP_EN 0x40 /* Response */ /* legacy bit mask (below) provided for backwards code compatibility */ #define CMD_RSP CMD_RSP_EN /* Response */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_RSP 0x0 #define CMD_LRSP_EN 0x80 /* Long Response */ /* legacy bit mask (below) provided for backwards code compatibility */ #define CMD_L_RSP CMD_LRSP_EN /* Long Response */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_L_RSP 0x0 #define CMD_INT_EN 0x100 /* Command Interrupt */ /* legacy bit mask (below) provided for backwards code compatibility */ #define CMD_INT_E CMD_INT_EN /* Command Interrupt */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_INT_E 0x0 #define CMD_PEND_EN 0x200 /* Command Pending */ /* legacy bit mask (below) provided for backwards code compatibility */ #define CMD_PEND_E CMD_PEND_EN /* Command Pending */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_PEND_E 0x0 #define CMD_EN 0x400 /* Command Enable */ /* legacy bit mask (below) provided for backwards code compatibility */ #define CMD_E CMD_EN /* Command Enable */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_E 0x0 /* Bit masks for RSI_RESP_CMD */ #define RESP_CMD 0x3f /* Response Command */ /* Bit masks for RSI_DATA_LGTH */ #define DATA_LENGTH 0xffff /* Data Length */ /* Bit masks for RSI_DATA_CONTROL */ #define DATA_EN 0x1 /* Data Transfer Enable */ /* legacy bit mask (below) provided for backwards code compatibility */ #define DTX_E DATA_EN /* Data Transfer Enable */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nDTX_E 0x0 #define DATA_DIR 0x2 /* Data Transfer Direction */ /* legacy bit mask (below) provided for backwards code compatibility */ #define DTX_DIR DATA_DIR /* Data Transfer Direction */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nDTX_DIR 0x0 #define DATA_MODE 0x4 /* Data Transfer Mode */ /* legacy bit mask (below) provided for backwards code compatibility */ #define DTX_MODE DATA_MODE /* Data Transfer Mode */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nDTX_MODE 0x0 #define DATA_DMA_EN 0x8 /* Data Transfer DMA Enable */ /* legacy bit mask (below) provided for backwards code compatibility */ #define DTX_DMA_E 0x8 /* Data Transfer DMA Enable */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nDTX_DMA_E 0x0 #define DATA_BLK_LGTH 0xf0 /* Data Transfer Block Length */ /* legacy bit mask (below) provided for backwards code compatibility */ #define DTX_BLK_LGTH 0xf0 /* Data Transfer Block Length */ #define CEATA_EN 0x100 /* CE-ATA operation mode enable */ #define CEATA_CCS_EN 0x200 /* CE-ATA CCS mode enable */ /* Bit masks for RSI_DATA_CNT */ #define DATA_COUNT 0xffff /* Data Count */ /* Bit masks for RSI_STATUS */ #define CMD_CRC_FAIL 0x1 /* CMD CRC Fail */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_CRC_FAIL 0x0 #define DAT_CRC_FAIL 0x2 /* Data CRC Fail */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nDAT_CRC_FAIL 0x0 #define CMD_TIMEOUT 0x4 /* CMD Time Out */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_TIMEOUT 0x0 #define DAT_TIMEOUT 0x8 /* Data Time Out */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nDAT_TIMEOUT 0x0 #define TX_UNDERRUN 0x10 /* Transmit Underrun */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nTX_UNDERRUN 0x0 #define RX_OVERRUN 0x20 /* Receive Overrun */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nRX_OVERRUN 0x0 #define CMD_RESP_END 0x40 /* CMD Response End */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_RESP_END 0x0 #define CMD_SENT 0x80 /* CMD Sent */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_SENT 0x0 #define DAT_END 0x100 /* Data End */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nDAT_END 0x0 #define START_BIT_ERR 0x200 /* Start Bit Error */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nSTART_BIT_ERR 0x0 #define DAT_BLK_END 0x400 /* Data Block End */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nDAT_BLK_END 0x0 #define CMD_ACT 0x800 /* CMD Active */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_ACT 0x0 #define TX_ACT 0x1000 /* Transmit Active */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nTX_ACT 0x0 #define RX_ACT 0x2000 /* Receive Active */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nRX_ACT 0x0 #define TX_FIFO_STAT 0x4000 /* Transmit FIFO Status */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nTX_FIFO_STAT 0x0 #define RX_FIFO_STAT 0x8000 /* Receive FIFO Status */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nRX_FIFO_STAT 0x0 #define TX_FIFO_FULL 0x10000 /* Transmit FIFO Full */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nTX_FIFO_FULL 0x0 #define RX_FIFO_FULL 0x20000 /* Receive FIFO Full */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nRX_FIFO_FULL 0x0 #define TX_FIFO_ZERO 0x40000 /* Transmit FIFO Empty */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nTX_FIFO_ZERO 0x0 #define RX_DAT_ZERO 0x80000 /* Receive FIFO Empty */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nRX_DAT_ZERO 0x0 #define TX_DAT_RDY 0x100000 /* Transmit Data Available */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nTX_DAT_RDY 0x0 #define RX_FIFO_RDY 0x200000 /* Receive Data Available */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nRX_FIFO_RDY 0x0 /* Bit masks for RSI_STATCL */ #define CMD_CRC_FAIL_STAT 0x1 /* CMD CRC Fail Status */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_CRC_FAIL_STAT 0x0 #define DAT_CRC_FAIL_STAT 0x2 /* Data CRC Fail Status */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nDAT_CRC_FAIL_STAT 0x0 #define CMD_TIMEOUT_STAT 0x4 /* CMD Time Out Status */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_TIMEOUT_STAT 0x0 #define DAT_TIMEOUT_STAT 0x8 /* Data Time Out status */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nDAT_TIMEOUT_STAT 0x0 #define TX_UNDERRUN_STAT 0x10 /* Transmit Underrun Status */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nTX_UNDERRUN_STAT 0x0 #define RX_OVERRUN_STAT 0x20 /* Receive Overrun Status */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nRX_OVERRUN_STAT 0x0 #define CMD_RESP_END_STAT 0x40 /* CMD Response End Status */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_RESP_END_STAT 0x0 #define CMD_SENT_STAT 0x80 /* CMD Sent Status */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_SENT_STAT 0x0 #define DAT_END_STAT 0x100 /* Data End Status */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nDAT_END_STAT 0x0 #define START_BIT_ERR_STAT 0x200 /* Start Bit Error Status */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nSTART_BIT_ERR_STAT 0x0 #define DAT_BLK_END_STAT 0x400 /* Data Block End Status */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nDAT_BLK_END_STAT 0x0 /* Bit masks for RSI_MASKx */ #define CMD_CRC_FAIL_MASK 0x1 /* CMD CRC Fail Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_CRC_FAIL_MASK 0x0 #define DAT_CRC_FAIL_MASK 0x2 /* Data CRC Fail Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nDAT_CRC_FAIL_MASK 0x0 #define CMD_TIMEOUT_MASK 0x4 /* CMD Time Out Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_TIMEOUT_MASK 0x0 #define DAT_TIMEOUT_MASK 0x8 /* Data Time Out Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nDAT_TIMEOUT_MASK 0x0 #define TX_UNDERRUN_MASK 0x10 /* Transmit Underrun Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nTX_UNDERRUN_MASK 0x0 #define RX_OVERRUN_MASK 0x20 /* Receive Overrun Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nRX_OVERRUN_MASK 0x0 #define CMD_RESP_END_MASK 0x40 /* CMD Response End Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_RESP_END_MASK 0x0 #define CMD_SENT_MASK 0x80 /* CMD Sent Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_SENT_MASK 0x0 #define DAT_END_MASK 0x100 /* Data End Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nDAT_END_MASK 0x0 #define START_BIT_ERR_MASK 0x200 /* Start Bit Error Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nSTART_BIT_ERR_MASK 0x0 #define DAT_BLK_END_MASK 0x400 /* Data Block End Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nDAT_BLK_END_MASK 0x0 #define CMD_ACT_MASK 0x800 /* CMD Active Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCMD_ACT_MASK 0x0 #define TX_ACT_MASK 0x1000 /* Transmit Active Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nTX_ACT_MASK 0x0 #define RX_ACT_MASK 0x2000 /* Receive Active Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nRX_ACT_MASK 0x0 #define TX_FIFO_STAT_MASK 0x4000 /* Transmit FIFO Status Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nTX_FIFO_STAT_MASK 0x0 #define RX_FIFO_STAT_MASK 0x8000 /* Receive FIFO Status Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nRX_FIFO_STAT_MASK 0x0 #define TX_FIFO_FULL_MASK 0x10000 /* Transmit FIFO Full Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nTX_FIFO_FULL_MASK 0x0 #define RX_FIFO_FULL_MASK 0x20000 /* Receive FIFO Full Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nRX_FIFO_FULL_MASK 0x0 #define TX_FIFO_ZERO_MASK 0x40000 /* Transmit FIFO Empty Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nTX_FIFO_ZERO_MASK 0x0 #define RX_DAT_ZERO_MASK 0x80000 /* Receive FIFO Empty Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nRX_DAT_ZERO_MASK 0x0 #define TX_DAT_RDY_MASK 0x100000 /* Transmit Data Available Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nTX_DAT_RDY_MASK 0x0 #define RX_FIFO_RDY_MASK 0x200000 /* Receive Data Available Mask */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nRX_FIFO_RDY_MASK 0x0 /* Bit masks for RSI_FIFO_CNT */ #define FIFO_COUNT 0x7fff /* FIFO Count */ /* Bit masks for RSI_CEATA_CONTROL */ #define CEATA_TX_CCSD 0x1 /* Send CE-ATA CCSD sequence */ /* Bit masks for RSI_ESTAT */ #define SDIO_INT_DET 0x2 /* SDIO Int Detected */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nSDIO_INT_DET 0x0 #define SD_CARD_DET 0x10 /* SD Card Detect */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nSD_CARD_DET 0x0 #define CEATA_INT_DET 0x20 /* Bit masks for RSI_EMASK */ #define SDIO_INT_DET_MASK 0x2 /* Mask SDIO Int Detected */ /* legacy bit mask (below) provided for backwards code compatibility */ #define SDIO_MSK SDIO_INT_DET_MASK /* Mask SDIO Int Detected */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nSDIO_MSK 0x0 #define SD_CARD_DET_MASK 0x10 /* Mask Card Detect */ /* legacy bit mask (below) provided for backwards code compatibility */ #define SCD_MASK SD_CARD_DET_MASK /* Mask Card Detect */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nSCD_MSK 0x0 #define CEATA_INT_DET_MASK 0x20 /* Bit masks for SDH_CFG */ /* Left in for backwards compatibility */ #define RSI_CLK_EN 0x1 /* legacy bit mask (below) provided for backwards code compatibility */ #define CLKS_EN RSI_CLK_EN /* Clocks Enable */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nCLKS_EN 0x0 #define SDIO4_EN 0x4 /* SDIO 4-Bit Enable */ /* legacy bit mask (below) provided for backwards code compatibility */ #define SD4E SDIO4_EN /* SDIO 4-Bit Enable */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nSD4E 0x0 #define MW_EN 0x8 /* Moving Window Enable */ /* legacy bit mask (below) provided for backwards code compatibility */ #define MWE MW_EN /* Moving Window Enable */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nMWE 0x0 #define RSI_RST 0x10 /* SDMMC Reset */ /* legacy bit mask (below) provided for backwards code compatibility */ #define SD_RST RSI_RST /* SDMMC Reset */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nSD_RST 0x0 #define PU_DAT 0x20 /* Pull-up SD_DAT */ /* legacy bit mask (below) provided for backwards code compatibility */ #define PUP_SDDAT PU_DAT /* Pull-up SD_DAT */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nPUP_SDDAT 0x0 #define PU_DAT3 0x40 /* Pull-up SD_DAT3 */ /* legacy bit mask (below) provided for backwards code compatibility */ #define PUP_SDDAT3 PU_DAT3 /* Pull-up SD_DAT3 */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nPUP_SDDAT3 0x0 #define PD_DAT3 0x80 /* Pull-down SD_DAT3 */ /* legacy bit mask (below) provided for backwards code compatibility */ #define PD_SDDAT3 PD_DAT3 /* Pull-down SD_DAT3 */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nPD_SDDAT3 0x0 /* Bit masks for RSI_RD_WAIT_EN */ #define SDIO_RWR 0x1 /* Read Wait Request */ /* legacy bit mask (below) provided for backwards code compatibility */ #define RWR SDIO_RWR /* Read Wait Request */ /* legacy bit mask (below) provided for backwards code compatibility */ #define nRWR 0x0 /* Bit masks for RSI_PIDx */ #define RSI_PID 0xff /* RSI Peripheral ID */ #ifdef _MISRA_RULES #pragma diag(pop) #endif /* _MISRA_RULES */ #endif /* _DEF_BF518_H */